Index of /~tajohnson/Co-Cure Cable/1.2m Co-Cure Cable lay-up Procedure by photo

[ICO]NameLast modifiedSizeDescription
[DIR]Parent Directory  -  
[IMG]1-Cables.JPG19-Aug-2010 22:48 2.0M 
[IMG]2-Cable Inspection.JPG19-Aug-2010 22:49 1.7M 
[IMG]3-Cable Inspection 2.JPG19-Aug-2010 22:49 2.0M 
[IMG]4-Cable Inspection 3.JPG19-Aug-2010 22:49 2.0M 
[IMG]5-Cable Inspection 4.JPG19-Aug-2010 22:50 1.9M 
[IMG]6-Clean Surface and Mask with 1mil Flashbreaker tape.JPG23-Aug-2010 21:21 1.9M 
[IMG]7-Clean Surface and Mask with 1mil Flashbreaker tape 2.JPG23-Aug-2010 22:03 2.0M 
[IMG]8-Clean Surface and Mask with 1mil Flashbreaker tape 3.JPG23-Aug-2010 22:27 1.9M 
[IMG]9-Trim excess tape from perimeter.JPG23-Aug-2010 22:33 2.1M 
[IMG]10-Masked Cable.JPG20-Aug-2010 01:39 2.0M 
[IMG]11-Masked Cable 2.JPG20-Aug-2010 01:39 2.1M 
[IMG]12-masked Cable close-up.JPG20-Aug-2010 01:40 1.6M 
[IMG]13- Abrade backside of cable with ScotchBrite.JPG22-Aug-2010 21:05 2.0M 
[IMG]13- Dust created by abrading backside.JPG22-Aug-2010 21:08 2.2M 
[IMG]14-Clean with Alcohol.JPG22-Aug-2010 21:10 1.8M 
[IMG]15-Layer 1,2 layed out.JPG22-Aug-2010 21:32 1.8M 
[IMG]16-Stacking layer 1,2.JPG22-Aug-2010 21:35 1.7M 
[IMG]17-Layer 1,2 stacked.JPG22-Aug-2010 21:40 1.8M 
[IMG]18-Layer 1,2 taped together to prevent moving.JPG23-Aug-2010 23:04 1.8M 
[IMG]19-Release ply for compacting.JPG23-Aug-2010 23:05 1.9M 
[IMG]20- Compact with Vacuum.JPG22-Aug-2010 21:46 1.8M 
[IMG]21-Flip part and remove backing.JPG22-Aug-2010 22:12 1.6M 
[IMG]22-Backing removed.JPG22-Aug-2010 22:13 1.8M 
[IMG]23-0 deg center ply.JPG22-Aug-2010 22:13 2.1M 
[IMG]24-90deg layer 3 layed out.JPG22-Aug-2010 22:14 1.9M 
[IMG]25-Layer 3.JPG22-Aug-2010 22:29 1.7M 
[IMG]26-Tape plys together.JPG23-Aug-2010 23:04 1.8M 
[IMG]27-Release ply for compacting.JPG23-Aug-2010 23:05 1.9M 
[IMG]28-Compact layer 1,2,3.JPG22-Aug-2010 21:46 1.8M 
[IMG]29-Remove backing from layer 3.JPG22-Aug-2010 22:30 1.8M 
[IMG]30-Add peal-ply to layup.JPG22-Aug-2010 22:38 1.8M 
[IMG]31-Flip stack and remove backing.JPG22-Aug-2010 22:30 1.8M 
[IMG]32-Place cable on stack.JPG23-Aug-2010 00:56 1.8M 
[IMG]33-Add peal ply to remaining exposed carbon.JPG23-Aug-2010 00:58 2.0M 
[IMG]34-Put release ply over stack.JPG24-Aug-2010 02:54 2.0M 
[IMG]35-Compact Again.JPG22-Aug-2010 21:46 1.8M 
[IMG]36-Flip Compacted stack so the Cable is on bottom.JPG23-Aug-2010 00:59 1.9M 
[IMG]37-Final covering of release ply -No wrinkles-.JPG23-Aug-2010 01:02 1.8M 
[IMG]38-Add single layer of breather-No wrinkles-compact-cook.JPG23-Aug-2010 23:07 1.9M 
[ ]Thumbs.db25-Aug-2010 12:10 356K 
Apache/2.2.15 (CentOS) Server at www-eng.lbl.gov Port 443