\relax 
\catcode`"\active
\catcode`<\active
\catcode`>\active
\@nameuse{es@quoting}
\citation{UDS}
\citation{vendor-visit}
\select@language{english}
\@writefile{toc}{\select@language{english}}
\@writefile{lof}{\select@language{english}}
\@writefile{lot}{\select@language{english}}
\@writefile{toc}{\contentsline {section}{\numberline {1}Status Report and Vendor}{1}}
\@writefile{toc}{\contentsline {section}{\numberline {2}Description}{1}}
\newlabel{pvs}{{2}{2}}
\@writefile{lof}{\contentsline {figure}{\numberline {1}{\ignorespaces Pressure Vessel, Side view}}{2}}
\newlabel{pve}{{2}{3}}
\@writefile{lof}{\contentsline {figure}{\numberline {2}{\ignorespaces Pressure Vessel, End View, Tracking end}}{3}}
\newlabel{xseclnocubar}{{2}{4}}
\@writefile{lof}{\contentsline {figure}{\numberline {3}{\ignorespaces Pressure Vessel/Detector Longitudinal Cross Section, without ICS (Cu) bars}}{4}}
\newlabel{xseclcubar}{{2}{4}}
\@writefile{lof}{\contentsline {figure}{\numberline {4}{\ignorespaces Pressure Vessel/Detector Longitudinal Cross Section, with ICS (Cu) bars}}{4}}
\citation{UDS}
\newlabel{xsectrans}{{2}{5}}
\@writefile{lof}{\contentsline {figure}{\numberline {5}{\ignorespaces Pressure Vessel/Detector Transverse Cross section, at EL gap}}{5}}
\newlabel{pv_table}{{2}{6}}
\@writefile{lot}{\contentsline {table}{\numberline {1}{\ignorespaces NEXT100 Pressure Vessel Parameters}}{6}}
\newlabel{params}{{1}{6}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.1}Design Standards}{6}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.2}Flanges and Sealing}{6}}
\newlabel{sniff}{{2.2}{7}}
\@writefile{lof}{\contentsline {figure}{\numberline {6}{\ignorespaces Double O-ring/sense port detail}}{7}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.3}Ports}{7}}
\newlabel{interface}{{2.3}{8}}
\@writefile{lof}{\contentsline {figure}{\numberline {7}{\ignorespaces EL Access Port/Interface flange with CF window}}{8}}
\newlabel{cm_nozzle}{{2.3}{8}}
\@writefile{lof}{\contentsline {figure}{\numberline {8}{\ignorespaces Central Manifold/ Nozzle Flange Seal}}{8}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.4}Bolting}{9}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.5}Supports}{9}}
\@writefile{toc}{\contentsline {subsection}{\numberline {2.6}Pressure Relief}{9}}
\newlabel{support1}{{2.5}{10}}
\@writefile{lof}{\contentsline {figure}{\numberline {9}{\ignorespaces Vessel (quasi) Kinematic Support design }}{10}}
\newlabel{support2}{{2.5}{11}}
\@writefile{lof}{\contentsline {figure}{\numberline {10}{\ignorespaces Vessel (quasi) Kinematic Support design, bottom view }}{11}}
\newlabel{support3}{{2.5}{12}}
\@writefile{lof}{\contentsline {figure}{\numberline {11}{\ignorespaces Vessel (quasi) Kinematic Support design Bottom Detail }}{12}}
\newlabel{support4}{{2.5}{12}}
\@writefile{lof}{\contentsline {figure}{\numberline {12}{\ignorespaces Vessel (quasi) Kinematic Support design, top Detail }}{12}}
\newlabel{gas_sys}{{2.6}{13}}
\@writefile{lof}{\contentsline {figure}{\numberline {13}{\ignorespaces Gas System Interface with vessel}}{13}}
\@writefile{toc}{\contentsline {section}{\numberline {3}Handling and Assembly}{13}}
\@writefile{lof}{\contentsline {figure}{\numberline {14}{\ignorespaces Hexapod Support Fixture, Attached to Torispheric Head}}{14}}
\newlabel{hx1}{{14}{14}}
\@writefile{lof}{\contentsline {figure}{\numberline {15}{\ignorespaces Hexapod Support Fixture, Attached to Torispheric Head}}{14}}
\newlabel{hx2}{{15}{14}}
\@writefile{toc}{\contentsline {section}{\numberline {4}Vessel Construction}{14}}
\bibcite{UDS}{1}
\@writefile{toc}{\contentsline {section}{\numberline {5}Fabrication Contracting Process}{15}}
\bibcite{vendor-visit}{2}