iMPACT Version: 
iMPACT log file Started on Wed Feb 21 16:54:42 2007

// *** BATCH CMD : setPreference -pref AutoSignature:FALSE
// *** BATCH CMD : setPreference -pref KeepSVF:FALSE
// *** BATCH CMD : setPreference -pref ConcurrentMode:FALSE
// *** BATCH CMD : setPreference -pref UseHighz:FALSE
// *** BATCH CMD : setPreference -pref svfUseTime:FALSE
// *** BATCH CMD : loadProjectFile -file"U:/Projects/SAO/VHDL/SAOTxBoard/sao_tx/sao_tx.ipf"
'1': Loading file 'u:/projects/sao/vhdl/saotxboard/sao_tx/top.jed' ...
done.
INFO:iMPACT:1777 - 
   Reading C:/Xilinx/xc9500xl/data/xc95288xl.bsd...
INFO:iMPACT:501 - '1': Added Device xc95288xl successfully.
----------------------------------------------------------------------
----------------------------------------------------------------------
Active mode is BS
// *** BATCH CMD : setMode -ss
// *** BATCH CMD : setMode -sm
// *** BATCH CMD : setMode -hw140
// *** BATCH CMD : setMode -spi
// *** BATCH CMD : setMode -acecf
// *** BATCH CMD : setMode -acempm
// *** BATCH CMD : setMode -pff
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
 Count ReleaseSemaphore rc = 298.
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
 Driver windrvr6.sys version = 7.0.0.0. LPT base address = 0378h.
 ECP base address = 0778h.
 ECP hardware is detected.
Cable connection established.
Connecting to cable (Parallel Port - LPT1) in ECP mode.
Checking cable driver.
 Driver xpc4drvr.sys version = 1.0.4.0. LPT base address = 0378h.
 Cable Type = 1, Revision = 3.
 Setting cable speed to 5 MHz.
Cable connection established.
PROGRESS_END - End Operation.
Elapsed time =      1 sec.
Attempting to identify devices in the boundary-scan chain configuration...// *** BATCH CMD : Identify 
PROGRESS_START - Starting Operation.
Identifying chain contents ....'1': : Manufacturer's ID =Xilinx xc95288xl, Version : 4
INFO:iMPACT:1777 - 
   Reading C:/Xilinx/xc9500xl/data/xc95288xl.bsd...
INFO:iMPACT:501 - '1': Added Device xc95288xl successfully.
----------------------------------------------------------------------
----------------------------------------------------------------------
done.
Chain TCK freq = 10000000.
Validating chain...
Boundary-scan chain validated successfully.
PROGRESS_END - End Operation.
Elapsed time =      0 sec.
// *** BATCH CMD : identifyMPM 
// *** BATCH CMD : assignFile -p 1 -file"U:/Projects/SAO/VHDL/SAOTxBoard/sao_tx/top.jed"
'1': Loading file 'U:/Projects/SAO/VHDL/SAOTxBoard/sao_tx/top.jed' ...
done.
INFO:iMPACT:501 - '1': Added Device xc95288xl successfully.
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
// *** BATCH CMD : Program -p 1 -e -defaultVersion 0 
PROGRESS_START - Starting Operation.
Chain TCK freq = 10000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': Erasing device...
'1': Erasure completed successfully.
'1': Programming device...
done.
'1': Putting device in ISP mode...done.
'1': Putting device in ISP mode...done.
'1': Programming completed successfully.
PROGRESS_END - End Operation.
Elapsed time =      4 sec.
// *** BATCH CMD : Program -p 1 -e -defaultVersion 0 
Updating config file U:/Projects/SAO/VHDL/SAOTxBoard/sao_tx/top.jed...
ERROR:iMPACT:2243 - A reference voltage has not been detected on the ribbon   cable
   	interface to the target system ( pin 2 ).  Check that power is applied
   	 to the target system and that the ribbon cable is properly seated at
   	 both ends.  The status LED on Parallel Cable IV will be GREEN if target
   	 voltage is in the proper range and applied to the correct pin.
// *** BATCH CMD : Program -p 1 -e -defaultVersion 0 
PROGRESS_START - Starting Operation.
Chain TCK freq = 10000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': Erasing device...
'1': Erasure completed successfully.
'1': Programming device...
done.
'1': Putting device in ISP mode...done.
'1': Putting device in ISP mode...done.
'1': Programming completed successfully.
PROGRESS_END - End Operation.
Elapsed time =      4 sec.
Cable is not connected.
// *** BATCH CMD : saveProjectFile -file"U:/Projects/SAO/VHDL/SAOTxBoard/sao_tx/sao_tx.ipf"